煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

Formation of porous polymer morphology by microsyneresis during divinylbenzene polymerization

This article describes the investigation of the importance of various reaction conditions on microsyneretic pore formation during polymerization of divinylbenzene (DVB) under so‐called “solvothermal” conditions. To induce microsyneretic pore formation, the most important parameter is an unusually high dilution of monomers with a “good” porogen solvating the polymer chains. High dilution and solvation of the growing poly(DVB) chains promote the prolongation of the polymer chains rather than their interconnection by crosslinking. Consequently, when the polymer gel density reaches the point where syneresis starts, the polymer network is geometrically too extensive to be broken up into precipitating entities and, instead, porogen droplets are formed within the continuous polymer gel. The pore geometry created by microsyneresis offers high surface area in wide mesopores and hence, high capacity for supporting functional groups or reactions with much better accessibility than narrow pores between polymer microspheres produced by macrosyneresis in conventional styrenic polymer supports. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 774–781     

Crosslinked poly(ethylene oxide) containing siloxanes fabricated through thiol‐ene photochemistry

Homogenous amphiphilic crosslinked polymer films comprising of poly(ethylene oxide) and polysiloxane were synthesized utilizing thiol‐ene “ click ” photochemistry. A systematic variation in polymer composition was Carried out to obtain high quality films with varied amount of siloxane and poly(ethylene oxide). These films showed improved gas separation performance with high gas permeabilities with good CO₂/N₂ selectivity. Furthermore, the resulting films were also tested for its biocompatibility, as a carrier media which allow human adult mesenchymal stem cells to retain their capacity for osteoblastic differentiation after transplantation. The obtained crosslinked films were characterized using differential scanning calorimetry, dynamic mechanical analysis, thermogravimetric analysis, FTIR, Raman‐IR , and small angle X‐ray scattering. The synthesis ease and commercial availability of the starting materials suggests that these new crosslinked polymer networks could find applications in wide range of applications. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1548–1557     

3D‐morphology reconstruction of nanoscale phase‐separation in polymer memory blends

In many organic electronic devices functionality is achieved by blending two or more materials, typically polymers or molecules, with distinctly different optical or electrical properties in a single film. The local scale morphology of such blends is vital for the device performance. Here, a simple approach to study the full 3D morphology of phase‐separated blends, taking advantage of the possibility to selectively dissolve the different components is introduced. This method is applied in combination with AFM to investigate a blend of a semiconducting and ferroelectric polymer typically used as active layer in organic ferroelectric resistive switches. It is found that the blend consists of a ferroelectric matrix with three types of embedded semiconductor domains and a thin wetting layer at the bottom electrode. Statistical analysis of the obtained images excludes the presence of a fourth type of domains. The criteria for the applicability of the presented technique are discussed. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1231–1237     

大豆脲酶诱导碳酸钙沉淀的多因素影响分析

本文探究了多个影响因素对大豆脲酶诱导碳酸钙沉淀(SICP)的影响,以优选出主要影响因素并提供其最佳范围。首先分析了脲酶浓度和温度对脲酶活性的影响;之后通过正交实验设计,进行25种工况的SICP水溶液实验,研究不同因素组合下Ca²⁺利用率的变化规律;最后借助扫描电子显微镜观测不同工况下生成碳酸钙的形态。结果表明:低温有利于脲酶的保存及活性发挥,5 ℃时脲酶活性能保持21 d以上;同一温度下,脲酶浓度越大,脲酶初始活性越高,脲酶完全失活所需时间越短。pH值、脲酶与胶结液体积比是影响Ca²⁺利用率的主要因素。为达到较高的Ca²⁺利用率,脲酶和胶结液最佳体积比为1,氯化钙与尿素最佳浓度比为1.5,Ca²⁺最佳浓度为1 mol/L。当脲酶浓度较低时生成的六面体状碳酸钙较多;随着脲酶浓度的增大,所沉淀的碳酸钙向球形转变。大豆中富含的天冬氨酸是控制碳酸钙形态的重要因素。     

Salen–Mg-doped NH2–MIL-101(Cr) for effective CO2 adsorption under ambient conditions

A novel metal-doped metal–organic framework (MOF) was developed by incorporating salen–Mg into NH₂–MIL-101(Cr) structure under ambient conditions. The Schiff base complex was successfully prepared by condensing salicylaldehyde with a free amino group and then coordinating metal ions. Such a structure can endow the sample with higher CO₂ adsorption performance. At 0°C and 1 bar, the salen–Mg-modified sample achieves the maximum adsorption capacity of 2.18 mmol g⁻¹ for CO₂, which was 5.8% higher than the pristine salen–MOF under the same conditions. Notably, the Freundlich model indicates that the CO₂ adsorption process of all samples conforms to reversible adsorption. However, the correlation coefficients (R²) of the Mg-doped sample are lower than that of the pristine sample. Besides, the CO₂/N₂ adsorption selectivity and isosteric heat also show a similar trend. These results indicate that the salen–Mg can enhance the interaction between the material and CO₂ molecules.     

Evaluating the impact of functional groups on membrane-mediated CO2/N2 gas separations using a common polymer backbone

Polymeric membranes have shown tremendous promise for the separation of CO₂ from flue gas streams. However, few systematic studies have been conducted to better understand the impact that chemical functionalities have on membrane-based gas separation performance. To address this gap, we herein describe the synthesis and gas separation performance of a series of vinyl-addition polynorbornenes bearing various CO₂-philic functional groups. To facilitate direct comparison between functional groups, each material was designed to maintain a common polymer backbone. Though the incorporation of CO₂-philic moieties within a dense polymeric membrane is frequently hypothesized to enhance CO₂ solubility, and thereby increase CO₂/N₂ selectivity, our results demonstrate that the incorporation of CO₂-philic groups onto a common polymer backbone do not necessarily result in increased gas separation performance. Experimental and computational results demonstrate that the incorporation of amidoxime groups onto a polynorbornene backbone increase CO₂/N₂ selectivity, whereas commonly employed ethereal side chains only increased permeability.     

Molecularly engineering polymeric membranes for H2/CO2 separation at 100–300 °C

Over the last two decades, polymers with superior H₂/CO₂ separation properties at 100–300 °C have gathered significant interest for H₂ purification and CO₂ capture. This timely review presents various strategies adopted to molecularly engineer polymers for this application. We first elucidate the Robeson's upper bound at elevated temperatures for H₂/CO₂ separation and the advantages of high-temperature operation (such as improved solubility selectivity and absence of CO₂ plasticization), compared with conventional membrane gas separations at ~35 °C. Second, we describe commercially relevant membranes for the separation and highlight materials with free volumes tuned to discriminate H₂ and CO₂, including functional polymers (such as polybenzimidazole) and engineered polymers by cross-linking, blending, thermal treatment, thermal rearrangement, and carbonization. Third, we succinctly discuss mixed matrix materials containing size-sieving or H₂-sorptive nanofillers with attractive H₂/CO₂ separation properties.     

Structure and gas transport characteristics of triethylene oxide-grafted polystyrene-b-poly(ethylene-co-butylene)-b-polystyrene

Polymeric membrane-based gas separation technology has significant advantages compared with traditional amine-based CO₂ separation method. In this work, SEBS block copolymer is used as a polymer matrix to incorporate triethylene oxide (TEO) functionality. The short ethylene oxide segment is chosen to avoid crystallization, which is confirmed by differential scanning calorimetry and wide-angle X-ray scattering characterizations. The gas permeability results reveal that CO₂/N₂ selectivity increased with increasing content of TEO functional group. The highest CO₂ permeability (281 Barrer) and CO₂/N₂ selectivity (31) were obtained for the membrane with the highest TEO incorporation (57 mol%). Increasing the TEO content in these copolymers results in an increase in CO₂ solubility and a decrease in C₂H₆ solubility. For example, as the grafted TEO content increased from 0 to 57 mol%, the CO₂ solubility and CO₂/C₂H₆ solubility selectivity increased from 0.72 to 1.3 cm³(STP)/cm³ atm and 0.47 to 1.3 at 35°C, respectively. The polar ether linkage in TEO-grafted SEBS copolymers exhibits favorable interaction with CO₂ and unfavorable interaction with nonpolar C₂H₆, thus enhancing CO₂/C₂H₆ solubility selectivity.     

Slippery liquid-infused porous surface via thermally induced phase separation for enhanced corrosion protection

Slippery liquid-infused porous surface (SLIPS) is a rising star in corrosion protection owing to its outstanding corrosive medium resistance and self-healing property. The large-area and facile fabrication of SLIPS remains a challenge lying on the way of its practical application. Herein, we develop a novel SLIPS based on a porous polyvinylidene fluoride (PVDF) substrate fabricated by thermally induced phase separation. A sphere-packing structure can be easily obtained by blade-coating followed by cooling. The SLIPS exhibits an extremely low sliding angle of 5.8° so that it can resist the fouling of even the Chinese ink, ascribing to its slippery dynamic surface with low surface energy. We also evaluated the anti-corrosion performance of the SLIPS and superhydrophobic PVDF coating by electrochemical impedance spectroscopy (EIS) and scanning Kelvin probe technique (SKP), both of which exhibited enhanced corrosion resistance in 3.5 wt% NaCl solution due to the physical oil and air barriers against the corrosive medium penetration. Nevertheless, the SLIPS coatings performed outstanding self-healing properties because of the high fluidity of infused oil to recover the surface damages, and the self-healing process was recorded by the SKP.